top of page
Search

Pump Station Flow Monitoring Guide for South African Water and Wastewater Sites

Writer: Saim Shoaib
Saim Shoaib
7 days ago
17 min read

The most reliable pump-station flow monitoring starts with one practical question: where is the flow actually measurable with confidence? In many South African water and wastewater pump stations, the best answer is not the wet well, and it is not always the pump discharge. It is usually a correctly installed meter on a full rising main, supported by level, pressure, pump runtime and alarm signals so that operators can see both flow rate and station behaviour.


That direct answer matters because pump stations rarely fail quietly. A blocked suction, ragged impeller, air-locked main, stuck non-return valve, overflowing wet well or faulty level sensor can all look similar if the only information available is “pump on” or “pump off”. Good flow monitoring gives the station a second voice. It shows whether water is moving, how much has moved, whether pumps are performing as expected, and when the numbers no longer match the site conditions.


For pump station flow monitoring South Africa, the practical design should suit local realities: long rising mains, intermittent power, variable inflow, high solids in sewage, ageing pipework, remote telemetry, limited maintenance windows and sites that may flood during summer storms. The instrument choice matters, but the installation and signal context matter just as much.


Wide-angle view of a municipal wastewater pump station with a wet well cover and above-ground rising main
Flow monitoring works best when the meter, pipework and site conditions are considered together.

What flow monitoring must prove at a pump station


A pump station is not only a transfer point. It is a control point, a risk point and often a billing or reporting point. Flow monitoring should answer clear operating questions.


At a minimum, the system should show:


  • Current flow rate while each pump runs

  • Totalised volume pumped per shift, day, month or event

  • Whether the running pump is producing expected flow

  • Whether flow stops when the pump stops

  • Whether wet well level drops at the correct rate

  • Whether the rising main is likely full, partially filled, air-bound or obstructed

  • Whether there are signs of backflow, leakage or failed valves

  • Whether alarms reach the PLC, SCADA or telemetry system correctly


The flow meter is only one part of this picture. A pump station also needs level, pressure, pump status and runtime signals to make flow data useful. Without context, a flow reading can be misread.


For example, a low flow reading may mean:


  • The pump is worn

  • The suction is blocked

  • The discharge valve is partly closed

  • Air is trapped in the rising main

  • The meter is not installed correctly

  • The pipe is not full

  • The wrong pump is running for the duty point

  • Solids are affecting the measurement

  • The level in the wet well is too low for stable pumping


A good design narrows the fault boundary. It helps the operator decide whether the problem is hydraulic, electrical, mechanical, instrumental or process-related.


Understand the measurement points before choosing a meter


Pump stations offer several possible points for measurement. Each has benefits and traps. The best location depends on whether the line is full, whether solids or air are present, and what the measurement will be used for.


Wet wells show inflow and storage behaviour


The wet well is where inflow collects before pumping. It is usually not the best place for direct flow measurement, especially in sewage applications. Flow can enter through one or more pipes. The wet well level rises and falls. Turbulence, foam, fats, floating debris and rags can interfere with instruments.


Still, the wet well is vital to flow monitoring.


Level measurement in the wet well helps calculate inflow trends and confirms whether pumped flow is believable. If the pump starts and the flow meter reports a healthy flow, the wet well level should fall. If the level does not fall, something is wrong.


Common wet well signals include:


  • Continuous level

  • High level alarm

  • High-high level alarm

  • Low level or dry-run protection

  • Pump start and stop levels

  • Overflow indication where fitted


Wet well level also helps identify infiltration and inflow problems. In many South African municipalities, stormwater entering sewer systems can overload wastewater pump stations during heavy rain. A level trend that rises sharply during rainfall, combined with long pump runtimes and high totalised flow, gives useful evidence for network investigations.


Pump discharge is useful but hydraulically busy


The pump discharge line is close to the pump and often easy to access. This can make it tempting as a flow meter location. It can work, but the hydraulic conditions near a pump are often poor.


Close to the discharge, flow may be unstable due to:


  • Elbows and reducers

  • Non-return valves

  • Isolation valves

  • Pump vibration

  • Swirl from the pump volute

  • Pulsing during start-up

  • Entrained air

  • Short straight pipe lengths


A meter fitted too close to these disturbances may give unstable or biased readings. It may still be useful for pump proving or local indication, but care is needed if the value is used for reporting, control or billing-type reconciliation.


The best discharge installation usually includes enough straight pipe and a permanently full section. If this is not possible, the design may need a different technology or a different location.


Rising mains are often the best full-pipe location


A rising main is usually the preferred place for direct flow measurement when it runs full and has a suitable section for installation. It carries the combined discharge from the pump station to the receiving point, treatment works, reservoir, break-pressure structure or gravity sewer.


Rising main flow measurement works well because it can represent the actual pumped volume leaving the station. It is also useful for comparing pump runtime with delivered volume.


A rising main meter can support:


  • Daily pumped volume reporting

  • Pump efficiency checks

  • Burst or leakage suspicion

  • Blockage detection

  • Pump performance comparison

  • Verification after maintenance

  • SCADA trend analysis


The main risk is assuming the pipe is full when it is not. High points, poorly placed air valves, low velocities and intermittent pumping can lead to air pockets or partially filled conditions. These can affect many meter types.


Open-channel points need a different approach


Some pump stations discharge into channels, manholes, flumes or treatment works inlet structures. These are not full-pipe conditions. A full-bore inline flow meter is not the right tool unless the pipe can be guaranteed full at the meter.


Open-channel flow measurement may use level-based methods, ultrasonic level sensors above a flume or weir, area-velocity sensors, or other site-specific arrangements. The success depends on the hydraulic control. If the channel backs up, drowns the weir or fills with debris, the flow calculation may become unreliable.


Open-channel measurement is useful where the site has:


  • Gravity inflow to a pump station

  • Pumped discharge into an open chamber

  • Treatment works inlet channels

  • Stormwater channels

  • Combined flows with variable depth


The key is to design around the actual water profile, not around the pipe size on a drawing.


Choosing the right flow meter technology


No single technology solves every pump-station problem. A good selection starts with the fluid, pipe condition, flow profile, installation access and required outputs.


The table below gives a practical starting point.


Site condition or need

Suitable technology

Where it works best

Watch-outs

Full sewage rising main with conductive liquid

Electromagnetic flow meter

Inline metering on pressurised, full pipes

Pipe must remain full. Installation needs suitable pipework and grounding practices.

Full potable water rising main

Electromagnetic or ultrasonic flow meter

Pumped mains, reservoir transfer, water distribution pumping

Air pockets and poor straight lengths can affect readings.

Existing pipe where cutting is difficult

Clamp-on ultrasonic flow meter

Temporary checks, retrofit monitoring, clean full pipes

Pipe material, liner, wall condition and solids can affect signal quality.

Open channel or partially filled structure

Ultrasonic level with flume or weir, or area-velocity method

Channels, inlet works, discharge chambers

Needs stable hydraulics and regular cleaning.

Dirty wastewater with rags and solids

Magmeter in full pipe, selected for wastewater duty

Pumped sewage rising mains

Electrode fouling, lining condition and ragging risks must be managed.

Pump performance checks

Temporary ultrasonic or permanent inline meter with pressure readings

Before and after maintenance, acceptance checks

Flow alone is not enough. Pressure and pump speed or runtime add context.

Remote municipal telemetry

Flow meter with pulse, 4 to 20 mA, relay and digital communications as required

SCADA, PLC, RTU or logger connections

Signal scaling and totaliser rollover must be checked during commissioning.


Electromagnetic meters for full-pipe wastewater and water


Electromagnetic flow meters are widely used in water and wastewater because they measure conductive liquids and have no obstruction in the bore. This makes them suitable for many sewage rising mains where solids are present.


They are a strong choice when:


  • The pipe runs full

  • The liquid is conductive

  • The installation can accept an inline meter

  • Solids are present but not extreme enough to block the pipe

  • A local display, totaliser and control outputs are needed


A magmeter does not solve poor hydraulics by itself. It still needs a good installation. Empty pipe conditions, badly placed valves, air pockets and electrical noise can create problems. In wastewater sites, electrode coating and build-up should form part of the maintenance plan.


Ultrasonic meters for retrofit, clean water and open channels


Ultrasonic flow measurement appears in two main pump-station roles.


The first is clamp-on or transit-time measurement on full pipes. This is useful where the pipe cannot easily be cut, where temporary verification is needed, or where a non-invasive check is required. It usually performs best on clean liquids and known pipe materials. Heavy solids, scale, poor pipe condition or linings can reduce signal quality.


The second is level-based open-channel measurement. An ultrasonic level sensor can measure depth in a channel, flume or weir arrangement, then convert that depth to flow using the correct relationship for the hydraulic structure. This is common at treatment works and some pump station discharge points.


Ultrasonic instruments need careful aiming, stable mounting and clean sight lines. Foam, turbulence, wind, condensation and obstructions can affect level readings.


Pressure and differential signals add useful context


Pressure is not a flow meter, but it is one of the best support signals at a pump station. A pressure transmitter on the discharge or rising main helps interpret flow changes.


For example:


  • High pressure with low flow may suggest a blockage, closed valve or high downstream head

  • Low pressure with low flow may suggest pump wear, suction problems or air binding

  • Normal pressure with no flow may suggest an instrument fault or valve issue

  • Sudden pressure changes may point to valve movement, pump trips or surge events


Pressure trends also help protect pipework and pumps. They are especially useful on long rising mains, hilly terrain and transfer schemes where static head changes strongly affect pump duty.


Level, runtime and status signals make flow data trustworthy


Flow should not be viewed alone. A pump station instrumentation package often combines:


  • Wet well level

  • Flow rate

  • Totalised flow

  • Discharge pressure

  • Pump running status

  • Pump fault status

  • Pump runtime hours

  • Valve status where available

  • Power fail and phase fail alarms

  • High level and overflow alarms


This mix allows useful logic. If pump 1 runs for 20 minutes, the station should record a corresponding volume. If pump 2 runs for the same period but delivers less volume under similar level and pressure conditions, maintenance can investigate the pump, impeller, valve or suction path.


This is where a wastewater flow meter, pump station instrumentation, SCADA flow monitoring and rising main flow measurement should be planned as one system rather than separate purchases.


Close-up view of an inline electromagnetic flow meter installed on a painted rising main with isolation valves
A full-pipe meter on the rising main can provide flow rate and totalised volume for the whole pump station.

Air, solids and partially filled pipes can make good meters look bad


Many pump-station flow problems are not caused by the instrument. They are caused by the fluid conditions at the measuring point.


Air changes the measurement environment


Air can enter a pump system through vortexing in the wet well, leaking suction pipework, low wet well levels, pump start turbulence, high points in the rising main or faulty air release arrangements.


Air pockets can:


  • Reduce the effective flow area

  • Create unstable velocity profiles

  • Cause noise in ultrasonic measurement

  • Lead to erratic full-pipe readings

  • Increase pump vibration

  • Make totalised flow unreliable


A good flow monitoring plan checks high points, air release locations and whether the meter sits in a section that remains full during all normal operating modes. In many installations, moving the meter to a lower section of pipe gives better results than changing the meter type.


Solids and ragging affect both measurement and maintenance


Wastewater pump stations handle grit, fats, wipes, rags and other solids. These affect pumps and instruments.


A full-bore electromagnetic meter is often well suited because it introduces no obstruction into the pipe. Even so, solids can still create problems if velocities are too low and settlement occurs. Build-up can affect electrodes or create coating in the pipe.


Open-channel measurement is more exposed. A flume, weir or channel sensor may need frequent cleaning if fats and screenings collect in the approach section.


Good practice includes:


  • Avoiding unnecessary obstructions in sewage lines

  • Keeping velocities high enough to reduce settlement where possible

  • Ensuring access for cleaning and inspection

  • Logging maintenance events against flow trends

  • Checking whether sudden flow loss follows a known blockage or pump clogging event


Partial pipes need partial-pipe methods


A full-pipe flow meter assumes the pipe is full. If the pipe runs half-full, the reading may be wrong or unavailable. This is common near gravity discharges, open outlets, oversized pipes and sections downstream of intermittent pumping.


If the pipe cannot be kept full, use a measurement method suited to open-channel or area-velocity conditions. Forcing a full-pipe meter into a partial-pipe application often leads to repeated call-outs and mistrust of the data.


SCADA, telemetry and alarms should be designed from the start


Flow monitoring becomes far more valuable when it reaches the people who need it. A local display is useful during site visits, but many South African stations are remote or unmanned for long periods. Telemetry and SCADA turn a meter into an operational tool.


Useful flow signals for a PLC or RTU


Common outputs and signals include:


  • 4 to 20 mA for live flow rate

  • Pulse output for totalised volume

  • Relay output for alarms

  • Digital communication where the control system supports it

  • Local totaliser value

  • Forward and reverse flow indication where relevant

  • Meter fault or empty pipe status, where available


The control philosophy should define units and scaling clearly. For example, the analogue signal may represent litres per second or cubic metres per hour. The totaliser may count cubic metres. Pulse values must be set so the PLC counts accurately without missing pulses during high flow.


Avoid vague tags such as `FLOW_1` with no engineering description. Better tag descriptions help operators and technicians understand the signal boundary.


A clear tag list might identify:


  • Station discharge flow rate

  • Station discharge totalised flow

  • Pump 1 running status

  • Pump 2 running status

  • Wet well level

  • Rising main pressure

  • Flow meter fault

  • High wet well level

  • No-flow while pump running alarm


Alarm logic should compare signals


Simple high and low flow alarms can help, but pump stations benefit from comparison alarms.


Examples include:


  • Pump running with no flow after a start delay

  • Wet well level rising while duty pump is running

  • Flow below expected band for selected pump

  • Flow above expected band, possible burst or bypass condition

  • Long pump runtime without level recovery

  • Flow meter fault with pump running

  • Reverse flow or unexpected flow when pumps are stopped

  • High pressure with low flow


Alarm delays matter. Pump start-up can create short unstable periods. A no-flow alarm that triggers instantly may become a nuisance. A practical delay allows the pump, valve and meter to stabilise before alarming.


Alarm setpoints should be based on site behaviour. If a station has one small jockey pump and two larger duty pumps, each pump may need a different expected flow range.


Totalised flow explains what runtime cannot


Pump runtime is useful, but it is not a volume measurement. Two pumps can run for the same time and deliver different volumes due to wear, blockages, head changes or voltage issues.


Totalised flow gives a better picture of:


  • Daily volume transferred

  • Wet weather loading

  • Pump performance change over time

  • Unaccounted differences between stations

  • Maintenance impact after cleaning or repair

  • Treatment works inflow contribution


Runtime and flow total work best together. If runtime rises but totalised volume does not rise, pump performance may be falling or inflow patterns may have changed. If totalised volume rises sharply during storms, infiltration may be present.


Installation details decide whether the readings are trusted


A strong meter in a poor installation still gives poor confidence. Many faults can be avoided during planning.


Choose a full and representative pipe section


The ideal full-pipe meter location has:


  • A pipe section that remains full in all normal operating conditions

  • Stable flow with limited swirl

  • Suitable straight lengths where the technology requires them

  • Safe access for inspection and maintenance

  • Protection from flooding, impact and vandalism where practical

  • Cabling that avoids damage and electrical interference

  • Enough space to remove or service equipment where needed


Avoid locations immediately after pumps, elbows, tees, partly open valves or discharge points unless the meter manufacturer’s installation guidance allows it and the signal can be verified.


On a rising main, check the pipe profile. A point that looks convenient at ground level may be close to a hydraulic high point where air collects.


Plan isolation and bypass needs


Wastewater and water pump stations cannot always be shut down easily. If the instrument must be removed for service, the pipework should allow safe isolation. In critical stations, a bypass or temporary pumping plan may be needed.


For municipal maintenance teams, access can matter as much as accuracy. A meter installed in a difficult or unsafe chamber may not be inspected often. A meter that can be reached, cleaned and checked is more likely to give long-term value.


Protect cables, panels and signal paths


Instrumentation failures often happen outside the sensor. Cable damage, water ingress, poor glands, unlabelled cores and unstable power supplies can all interrupt flow monitoring.


A reliable installation should provide:


  • Correct cable routing and mechanical protection

  • Dry, accessible junction boxes where used

  • Proper gland sealing

  • Clear wire numbering and labels

  • Surge and earthing practices suited to the site design

  • Stable power supply to the transmitter and telemetry

  • Separation from high-power cables where needed


South African pump stations often face lightning, load interruptions and harsh outdoor conditions. The design should make it easy to distinguish an instrument fault from a power, panel or communication fault.


Verification and maintenance keep the system credible


Commissioning proves that the meter was installed and configured correctly. Regular verification proves that the readings still make sense.


Commissioning checklist for pump-station flow monitoring


Use this checklist before accepting a new or upgraded installation.


  • Confirm the measurement purpose Reporting, control, pump proving, leakage detection and alarm protection may need different signal quality.


  • Confirm the pipe condition Check pipe size, material, lining, direction of flow, full-pipe condition and access.


  • Confirm hydraulic suitability Check straight lengths, valve positions, high points, air release points and turbulence sources.


  • Confirm instrument installation Check orientation, grounding or bonding where required, cable entries, mounting and protection.


  • Confirm configuration Check pipe diameter, units, analogue scaling, pulse value, damping, low-flow cut-off and totaliser settings.


  • Confirm PLC or RTU signals Test live flow, total, fault status and alarms from field device to control system.


  • Confirm pump logic Run each pump and check that flow, level movement, pressure and pump status agree.


  • Confirm alarm delays Test no-flow, low-flow, high-level and meter fault alarms with practical delays.


  • Confirm totaliser behaviour Check that totalised volume increments correctly and does not reset unexpectedly.


  • Confirm operator displays Check that SCADA values use clear units and meaningful names.


  • Confirm documentation Record configuration, wiring, tag names, drawings, calibration or verification records and maintenance notes.


  • Confirm handover training Show operators what normal flow, low-flow, meter fault and communication fault conditions look like.


Ongoing checks that catch problems early


Maintenance does not need to be complicated, but it must be consistent. A practical schedule should include visual inspections, trend reviews and simple comparisons.


Useful checks include:


  • Compare flow while pump 1 runs with flow while pump 2 runs

  • Compare daily totalised flow with wet well level trends

  • Check whether flow drops after rainy periods due to ragging or grit movement

  • Inspect open-channel sensors for foam, spider webs, fats or debris

  • Check meter chambers for flooding

  • Review fault logs for intermittent empty pipe or signal loss warnings

  • Confirm that pulse totals in the PLC agree with the meter totaliser

  • Record pump maintenance dates against flow trend changes


The most useful maintenance record is often a simple note: what changed, when it changed and what the flow did afterwards.


South African water and wastewater scenarios


The following scenarios show how flow monitoring decisions change from site to site.


Small municipal sewage pump station with high rag loading


A small town station pumps sewage from a wet well to a gravity sewer or treatment works. The wet well collects fats, rags and grit. Operators receive complaints when overflows occur after storms.


Best approach:


  • Measure continuous wet well level

  • Fit a full-bore meter on the full rising main if the pipe conditions allow it

  • Monitor pump runtime and no-flow alarms

  • Use totalised flow to compare dry weather and wet weather loading

  • Add practical maintenance access for cleaning and inspection


The fault boundary becomes clearer. If the pump runs but flow is low and wet well level continues to rise, maintenance can check pump clogging, blocked suction, valve position or rising main blockage.


Potable water transfer pump station feeding a reservoir


A water station transfers treated water to a reservoir. Operators need to know daily pumped volume and whether the transfer pumps are meeting demand. The liquid is cleaner than sewage, but air at high points may be present.


Best approach:


  • Use full-pipe measurement on the delivery main

  • Add discharge pressure measurement

  • Totalise pumped volume to the reservoir

  • Trend flow against reservoir level and pump runtime

  • Alarm on no-flow with pump running and unexpected low flow


Clamp-on ultrasonic measurement may be useful for temporary checks, while a permanent inline meter may suit long-term reporting and control where pipework allows.


Long rising main over uneven terrain


A wastewater pump station sends flow over a long rising main with high and low points. Operators see unstable flow readings and intermittent pump trips.


Best approach:


  • Survey the pipe profile and identify air collection points

  • Check air release arrangements and valve status

  • Locate the flow meter in a section that remains full

  • Add pressure measurement to interpret flow changes

  • Use SCADA trends to compare pressure spikes, flow drops and pump trips


In this scenario, changing the meter before checking the hydraulics may waste time. Air management may be the real issue.


Treatment works inlet with changing channel depth


A treatment works receives pumped and gravity flows into an inlet channel. The channel does not run full, and backwater can occur during high flows.


Best approach:


  • Use open-channel methods suited to the hydraulic structure

  • Ensure stable approach flow and regular cleaning

  • Avoid relying on a full-pipe meter where the pipe is not full

  • Alarm on sensor fault, high level and abnormal flow

  • Compare inlet total with pump station totals where possible


Open-channel flow is practical, but the channel must be kept in a measurable condition.


Fault boundaries help teams respond faster


A good monitoring system does not diagnose every problem automatically. It gives the team enough evidence to choose the next action.


A useful fault boundary separates five areas.


Hydraulic faults include air pockets, blocked mains, closed valves, high downstream head and partial-pipe conditions.


Mechanical faults include worn impellers, ragged pumps, damaged non-return valves and blocked suction lines.


Electrical and control faults include pump trips, incorrect duty selection, failed contactors, unstable power and faulty level control.


Instrumentation faults include sensor fouling, incorrect scaling, cable damage, transmitter faults and empty pipe indications.


Telemetry and SCADA faults include lost communication, wrong units, incorrect tag mapping, failed pulse counting and alarm configuration errors.


When flow, level, pressure and pump status are all trended together, the fault boundary becomes much easier to place.


Frequently asked questions about pump station flow monitoring


Where should a flow meter be installed at a pump station?


The best location is usually a full, pressurised rising main with stable flow and safe access. The pipe should remain full during normal operation. Avoid locations too close to pumps, elbows, valves or high points where air collects unless the installation has been checked carefully.


Can flow be measured inside a wet well?


Wet wells are better suited to level measurement than direct flow measurement. Turbulence, foam, rags, fats and changing levels often make direct flow measurement difficult. Wet well level is still very useful when compared with pump runtime and discharge flow.


What is the best wastewater flow meter for a sewage rising main?


For many full-pipe sewage rising mains, an electromagnetic flow meter is a practical choice because it has no obstruction in the bore and suits conductive liquids. The final selection still depends on pipe condition, fullness, solids, access, outputs and maintenance needs.


Why does the flow reading drop when the pump is still running?


The cause may be pump wear, ragging, suction blockage, a partly closed valve, air in the rising main, changing downstream head, or an instrument issue. Check pressure, wet well level movement, pump current or status, valve positions and recent maintenance history before blaming the meter.


Is pump runtime enough to estimate pumped volume?


Runtime can give a rough indication, but it is not a flow measurement. Pump performance changes over time, and two pumps may deliver different volumes over the same runtime. Totalised flow gives a more reliable record of actual pumped volume.


What signals should be sent to SCADA?


Useful signals include live flow rate, totalised flow, meter fault status, wet well level, discharge pressure, pump running status, pump fault status and key alarms such as high level, no-flow while pump running and low-flow conditions. The values should use clear engineering units and tested scaling.


The practical takeaway


Reliable pump-station flow monitoring is built around the whole station, not only the meter. Start by deciding what the measurement must prove. Then choose a location where the fluid conditions are measurable, usually a full rising main for pressurised systems or a proper open-channel arrangement where the flow is not full-pipe.


Support the flow reading with level, pressure, pump status, runtime and totalised volume. Send the right signals to the PLC, RTU or SCADA system. Test the alarms under real pump conditions. Keep the installation accessible enough for maintenance teams to inspect, clean and verify.


For South African water and wastewater sites, that practical approach gives better alarms, more useful trends and faster fault finding when the station is under pressure.


 
 
 

Comments


 42 Hasivuna Agatha Tzaneen 0850 South Africa

+27 82 526 0068

f0ff29_359cf127ea414be4b6f362e060bc1cf5~mv2.jpeg

Copyright © 2026 DHS Instruments. All Rights Reserved

bottom of page